Manufacturers

DLE 20cc Gas Engine

  • Shipping Weight: 5lbs
  • Manufactured by: DLE

Rs.26,268.75  Rs.21,014.84
Save: 20% off

Sold Out
This is the DLE 20cc Gasoline Powered Engine with Electronic Ignition

FEATURES:
Two sealed bearings on crankshaft-simple design for lighter weight
Beam mounting allows easy fit in the same mount as comparable glow
engines
Aluminum alloy crankcase with advanced CNC machining
Rear mounted pumper carburetor ensures easier installation and smooth
idling and dependable fuel flow during flights
Fully automatic electronic ignition

INCLUDES:
Engine, spark plug, ignition, muffler, muffler gasket, two 5x20mm
muffler bolts and instruction manual

REQUIREMENTS:
Gasoline with at least 87 octane rating
2-cycle oil, mix ratio for this engine is 30 parts gas to one part
oil and must be followed exactly for warranty consideration
and optimum performance
4.8 - 6V NiMH/NiCd, or 6.6V LiFe or 7.4V LiPo battery for ignition
(separate receiver style pack can be used)

**NOTE, If ignition module is the A-02 model it has a built-in
voltage regulator. Model A-02 designation is located above the
word "Ignition" on top of the case**

LiPo & LiFe batteries require voltage regulator on older A-01
ignition module

Propeller and field equipment

SPECIFICATIONS:
Output Power: 2.5 HP at 9,000 RPM
Idle Speed: 1,750 RPM
Static Thrust: 6 kg Pulling Force/100 meters altitude
5.3 kg Pulling Force/1,800 meters altitude
Displacement: 1.22cu in (20cc)
Bore and Stroke: 1.3 x 1.0" (32 x 25mm)
Compression Ratio: 10.5:1
Weight: Engine: 22.93oz.(650g)
Exhaust: 1.76oz (50g)
Ignition: 4.23oz (120g)
Total: 28.9oz (820g)
Gasoline/Oil Mixture: 30:1
Gasoline Octane Rating: 87-93
Recommended Propellers: 14x10, 15x8, 16x6, 16x8, 17x6, 18x6
(break-in prop not specified)
Ignition Battery: 4.8V min,max as marked on electronic ignition unit.
If marked 6V max, BEC required if LiPo battery used.
Newer ones may be marked 4.8V to 8.4V.
Replacement Spark Plug: CM3, DLEG2126
Spark Plug Gap: 0.018 - 0.020"
Plug Installation Torque: 7 - 8ft-lbs
Carburetor Adjustments;
Low Speed Needle: 1.5 turns out as a starting point, adjust for a
smooth idle and a reliable transition to high throttle
High Speed Needle: 1.5-2 turns out from closed, adjust needle to peak
RPM, if engine slows or dies at full throttle, the high-speed
mixture is likely too lean
Height from bottom/Crankcase to top of Cylinder Head: 5.4" (138mm)
Height/bottom/of Mounting Tab to top of Cylinder Head: 3.4" (87.5mm)
Width of Cylinder Head: 2.5" (65mm)
Width at Mounting Tabs: 2.8" (70.5mm)
Distance/Mounting Hole Centers Same Side: 1.0" (26mm)
Distance/Mounting Hole Centers Opposite Side: 2.4" (60mm)
Height of Exhaust Opening: 0.42" (10.8mm)
Width of Exhaust Opening: 0.83" (21mm)
Length from Carburetor to Front Bearing: 4.5" (114mm)
Length from Carburetor to Prop Hub: 5.1" (130mm)
Total Height of Muffler including Exhaust Pipe: 3.8" (96mm)
Center of Muffler Exhaust Opening to end of Pipe: 2.4" (61mm)
Muffler Width: 2" (52.1mm)
Exhaust Pipe Inner Diameter: 0.56" (14.2mm)
Crankshaft thread size: 8mm x 1mm

COMMENTS:
To avoid permanent damage to the electronic ignition system, NEVER
turn your DLE engine over with the system switched on and the plug
not installed.

This product was added to our catalog on Sunday 12 January, 2014.

Manufacturer Info

Who's Online

There currently are 338 guests and 
1 member online.
Copyright © 2024 RCDhamaka. Powered by RCDhamaka